Instant Quote Shop Filters Call Air Bros

St. Petersburg, FL

air-bros-team-with-truck

The Best AC Repair in St. Petersburg, FL — From Technicians Your Neighbors Already Trust

When your AC quits in the middle of a St. Pete summer, you don't want a stranger in an unmarked van. You want a technician your neighbors already know and trust. Air Bros Air Conditioning & Electrical has been fixing air conditioners in St. Petersburg since 2020, but our roots run deeper — founder Ricky Orta grew up learning the trade from his father and has been a licensed HVAC contractor since 2006. That local, hands-on experience is why homeowners from Historic Kenwood to Snell Isle call us the best AC repair company in St. Petersburg.

We're headquartered right here in the Shore Acres neighborhood, so when you call, you're not routed to a call center — you're talking to the same local team that services your street.

Call us at 727-217-6148 or contact us online today for all of your HVAC, indoor air quality and electrical needs.

Meet the technicians who service St. Petersburg

What to expect when we show up

Calling a repair company you've never used before shouldn't feel like a gamble. Here's exactly how an Air Bros service call goes, every time.

You'll get a heads-up before we arrive, then a uniformed technician in a marked Air Bros vehicle shows up in the window we promised. We diagnose the whole system — not just the obvious symptom — then explain what we found and what your options are before any work starts. You approve the price up front, we make the repair, and we don't leave until we've confirmed the system is cooling the way it should.

Every technician is a background-checked, drug-tested Air Bros employee — never a subcontractor — and each one is trained to service every major AC and heat pump brand. It's the kind of consistency you can only get from a local team that answers to its own name.

And if something isn't right? Our 100% satisfaction guarantee means we make it right.

Signs you need AC repair

St. Petersburg's heat and humidity push air conditioners harder than almost anywhere else in the country. Call for AC repair if you notice:

  • Warm air blowing from vents, or the system running constantly without cooling
  • Water pooling around your air handler (a common issue in St. Pete's older homes with attic-run drain lines)
  • Musty odors or visible mold near vents — a sign of a clogged condensate line or dirty coil
  • Rising humidity indoors despite the AC running
  • Short cycling, tripped breakers, or a system that won't turn on at all

Our technicians diagnose the full system on every call — refrigerant charge, temperature split, electrical connections, and drain line — so you get a real fix, not a temporary patch.

Comprehensive HVAC Services in St. Petersburg

We offer a full range of heating and cooling services to keep your St. Petersburg, FL, home comfortable year-round:

  • Air Conditioning: From AC repair and AC installation to routine maintenance, we ensure your cooling system keeps you comfortable during those hot Florida summers. We offer same-day service for AC emergencies, so you never have to suffer in the heat.
  • Heating: Stay warm and cozy in the winter with our comprehensive heating services. We repair and install all types of heating systems, including furnaces and heat pumps, and offer preventative maintenance to keep your system running efficiently.
  • Indoor Air Quality: Improve your indoor air quality with our dehumidifier and UV light installation services. We'll help you control excess humidity and eliminate airborne contaminants, creating a healthier home environment.
  • Ductwork: Ensure optimal airflow and energy efficiency with our ductwork repair and installation services. We can address leaks and damage, and design a system that's perfect for your home.
  • Pool Heater Services: Extend your swim season with our pool heater installation and repair services.
  • Electrical Services: From outlet and switch replacements to ceiling fan installations to whole-house surge protector installations, we have the experts to handle your electrical service needs.

Our experienced technicians are skilled in all aspects of HVAC service and are dedicated to providing top-quality workmanship and customer care.

Why Choose Air Bros?

  • Local Expertise: We understand the unique climate challenges of St. Petersburg.
  • Fast and Reliable Service: We offer same-day service for AC emergencies and prioritize prompt service for all your HVAC needs.
  • Experienced Technicians: Our team is highly trained and experienced in all aspects of HVAC service.
  • Upfront Pricing: We provide transparent pricing with no hidden costs.
  • Customer Satisfaction Guaranteed: Your comfort and satisfaction are our top priorities.

Contact Air Bros Today!

Whether you need emergency AC repair, a new heating system installation, or any other HVAC service, Air Bros is here to help. Contact us today for a free consultation or to schedule a service appointment. We're proud to be your trusted HVAC partner in St. Petersburg!

Call us at 727-217-6148 or contact us online today!

Recent Jobs and Reviews in St. Petersburg, FL

St. Petersburg, FL at a glance

Air Bros Air Conditioning & Electrical has completed 25 jobs in St. Petersburg, FL in December 2025.

The most recent job was on December 16, 2025.

Air Bros Air Conditioning & Electrical has completed 1,919 jobs in St. Petersburg, FL in the last 12 months. The first job there was in December 2024.

Job Locations and Reviews

Performed Maitenences on systems. Cleaned/treated drain lines and primary drain pans. Cleaned condenser coils. Evaporator coils are clean. Verified safety float switchs functionality. Checked amp draw on compressors. Checked amp draw on fan motors. Checked capacitors are within factory range. Start/run capacitor on condenser #1 is out of factory range. Replaced capacitor.  Made sure all connections are tight. Systems are cooling with 20° temperature splits at this time. Verified systems heat properly.
Performed Maitenences on systems. Cleaned/treated drain lines and primary drain pans. Cleaned condenser coils. Evaporator coils are clean. Verified safety float switchs functionality. Checked amp draw on compressors. Checked amp draw on fan motors. Checked capacitors are within factory range. Start/run capacitor on condenser #1 is out of factory range. Replaced capacitor.  Made sure all connections are tight. Systems are cooling with 20° temperature splits at this time. Verified systems heat properly.
Michael A.
Michael A. Checked in
Performed Maitenences on systems. Cleaned/treated drain lines and primary drain pans. Cleaned condenser coils. Evaporator coils are clean. Verified safety float switchs functionality. Checked amp draw on compressors. Checked amp draw on fan motors. Checked capacitors are within factory range. Start/run capacitor on condenser #1 is out of factory range. Replaced capacitor. Made sure all connections are tight. Systems are cooling with 20° temperature splits at this time. Verified systems heat properly.
St. Petersburg, FL 33704
On arrival found unit not cooling due to broken thermostat wire on roof for condenser. Wire was pulled from service panel possibly from roofer tripping over wire. Replaced section of bad thermostat wire. Start and test. Pressures good. Temp split good. Compressor noisy on start up. Made client aware possible compressor failure in near future. Unit cooling at this time.
On arrival found unit not cooling due to broken thermostat wire on roof for condenser. Wire was pulled from service panel possibly from roofer tripping over wire. Replaced section of bad thermostat wire. Start and test. Pressures good. Temp split good. Compressor noisy on start up. Made client aware possible compressor failure in near future. Unit cooling at this time.
Justin G.
Justin G. Checked in
On arrival found unit not cooling due to broken thermostat wire on roof for condenser. Wire was pulled from service panel possibly from roofer tripping over wire. Replaced section of bad thermostat wire. Start and test. Pressures good. Temp split good. Compressor noisy on start up. Made client aware possible compressor failure in near future. Unit cooling at this time.
St. Petersburg, FL 33710
Furnish and install the following 
Ruud 3 ton 15.2 seer2 heat pump split system with 5kw heater
Hurricane pad
Anchor condenser 
Homeline breakers 30/30
Relocate condenser around corner of home
Insulate copper 
Add disconnect to end of existing electrical whip for condenser
New metal insulated stand
Condensate pump
New supply plenum
Primary float switch
Remove existing equipment 
Connect to existing ducts and electrical 
Seal unit to code
Tax labor and permit included
10 year parts warranty 
3 year labor warranty 
Client approved 0% for 18 month financing
Furnish and install the following 
Ruud 3 ton 15.2 seer2 heat pump split system with 5kw heater
Hurricane pad
Anchor condenser 
Homeline breakers 30/30
Relocate condenser around corner of home
Insulate copper 
Add disconnect to end of existing electrical whip for condenser
New metal insulated stand
Condensate pump
New supply plenum
Primary float switch
Remove existing equipment 
Connect to existing ducts and electrical 
Seal unit to code
Tax labor and permit included
10 year parts warranty 
3 year labor warranty 
Client approved 0% for 18 month financing
Martin W.
Martin W. Checked in
Furnish and install the following Ruud 3 ton 15.2 seer2 heat pump split system with 5kw heater Hurricane pad Anchor condenser Homeline breakers 30/30 Relocate condenser around corner of home Insulate copper Add disconnect to end of existing electrical whip for condenser New metal insulated stand Condensate pump New supply plenum Primary float switch Remove existing equipment Connect to existing ducts and electrical Seal unit to code Tax labor and permit included 10 year parts warranty 3 year labor warranty Client approved 0% for 18 month financing
St. Petersburg, FL 33713
Furnish and install the following 
3 ton Ruud 19 seer2 heat pump with 5kw heater
Full inverter 
Ruud thermostat
Anchor condenser
Condensate pump
Surge protector 
4” media filter and housing
Client to remove ceiling to access back of plenum to seal and remove old duct. 
Uv light
Relocate thermostat
Primary and secondary float
Keep metal pan
Remove existing equipment 
Connect to existing ducts and electrical
Seal unit to code
Tax labor and permit included 
10 year parts warranty 
3 year labor warranty 
$11,900.00
Unit eligible for $2000.00 tax credit

Mitsubishi 4 head mini split heat pump
3 ton condenser
Line set
Drains
Line cover
Electrical
Surge protector 
Wall mount bracket
10 year parts warranty 
3 year labor warranty 
Tax labor and permit included 
$15,900.00
Furnish and install the following 
3 ton Ruud 19 seer2 heat pump with 5kw heater
Full inverter 
Ruud thermostat
Anchor condenser
Condensate pump
Surge protector 
4” media filter and housing
Client to remove ceiling to access back of plenum to seal and remove old duct. 
Uv light
Relocate thermostat
Primary and secondary float
Keep metal pan
Remove existing equipment 
Connect to existing ducts and electrical
Seal unit to code
Tax labor and permit included 
10 year parts warranty 
3 year labor warranty 
$11,900.00
Unit eligible for $2000.00 tax credit

Mitsubishi 4 head mini split heat pump
3 ton condenser
Line set
Drains
Line cover
Electrical
Surge protector 
Wall mount bracket
10 year parts warranty 
3 year labor warranty 
Tax labor and permit included 
$15,900.00
Justin G.
Justin G. Checked in
Furnish and install the following 3 ton Ruud 19 seer2 heat pump with 5kw heater Full inverter Ruud thermostat Anchor condenser Condensate pump Surge protector 4” media filter and housing Client to remove ceiling to access back of plenum to seal and remove old duct. Uv light Relocate thermostat Primary and secondary float Keep metal pan Remove existing equipment Connect to existing ducts and electrical Seal unit to code Tax labor and permit included 10 year parts warranty 3 year labor warranty $11,900.00 Unit eligible for $2000.00 tax credit Mitsubishi 4 head mini split heat pump 3 ton condenser Line set Drains Line cover Electrical Surge protector Wall mount bracket 10 year parts warranty 3 year labor warranty Tax labor and permit included $15,900.00
St. Petersburg, FL 33713
Justin G.
Justin G. Checked in
Found unit not running due to condensate pump being unplugged and full of water. Plugged in pump. Unit started.
St. Petersburg, FL 33703
Inspect electrical and pull permits to allow Duke to make up connections to home and provide temporary receptacles for construction

Replaced bad gfi
Inspect electrical and pull permits to allow Duke to make up connections to home and provide temporary receptacles for construction

Replaced bad gfi
Griffin K.
Griffin K. Checked in
Inspect electrical and pull permits to allow Duke to make up connections to home and provide temporary receptacles for construction Replaced bad gfi
St. Petersburg, FL 33704
Performed Maitenence on system. Cleaned/treated drain line and primary drain pan. Cleaned condenser coils. Evaporator coils are clean. Verified safety float switch functionality. Checked amp draw on compressor. Checked amp draw on fan motor. Checked capacitor is not within factory range. replaced capacitor. Inspected Contactar. Made sure all connections are tight. System is cooling with a 20° temperature split at this time. Verified system heating functions.
Performed Maitenence on system. Cleaned/treated drain line and primary drain pan. Cleaned condenser coils. Evaporator coils are clean. Verified safety float switch functionality. Checked amp draw on compressor. Checked amp draw on fan motor. Checked capacitor is not within factory range. replaced capacitor. Inspected Contactar. Made sure all connections are tight. System is cooling with a 20° temperature split at this time. Verified system heating functions.
Michael A.
Michael A. Checked in
Performed Maitenence on system. Cleaned/treated drain line and primary drain pan. Cleaned condenser coils. Evaporator coils are clean. Verified safety float switch functionality. Checked amp draw on compressor. Checked amp draw on fan motor. Checked capacitor is not within factory range. replaced capacitor. Inspected Contactar. Made sure all connections are tight. System is cooling with a 20° temperature split at this time. Verified system heating functions.
St. Petersburg, FL 33703
Performed Maitenence on system. Cleaned/treated drain line and primary drain pan. Inspected condenser coils. Evaporator coils are mostly clean. Verified safety float switch functionality. Checked amp draw on compressor. Checked amp draw on fan motor. Checked capacitors are within factory range. Inspected Contactar. Made sure all connections are tight. System is cooling with a 20° temperature split at this time. Verified heating operations. Spoke with client about Maitenence plan. 
Advised client to buy slightly bigger filters to cover entire evaporator coils.
Performed Maitenence on system. Cleaned/treated drain line and primary drain pan. Inspected condenser coils. Evaporator coils are mostly clean. Verified safety float switch functionality. Checked amp draw on compressor. Checked amp draw on fan motor. Checked capacitors are within factory range. Inspected Contactar. Made sure all connections are tight. System is cooling with a 20° temperature split at this time. Verified heating operations. Spoke with client about Maitenence plan. 
Advised client to buy slightly bigger filters to cover entire evaporator coils.
Michael A.
Michael A. Checked in
Performed Maitenence on system. Cleaned/treated drain line and primary drain pan. Inspected condenser coils. Evaporator coils are mostly clean. Verified safety float switch functionality. Checked amp draw on compressor. Checked amp draw on fan motor. Checked capacitors are within factory range. Inspected Contactar. Made sure all connections are tight. System is cooling with a 20° temperature split at this time. Verified heating operations. Spoke with client about Maitenence plan. Advised client to buy slightly bigger filters to cover entire evaporator coils.
St. Petersburg, FL 33703
On arrival found unit not cooling due to bad blower motor. Will submit estimates for repair and replacement options. Unit not operating at this time.
On arrival found unit not cooling due to bad blower motor. Will submit estimates for repair and replacement options. Unit not operating at this time.
Justin G.
Justin G. Checked in
On arrival found unit not cooling due to bad blower motor. Will submit estimates for repair and replacement options. Unit not operating at this time.
St. Petersburg, FL 33710
RUUD Equipment (2 Stage)
Install New Air Handler 
Install Air Handler UV System
Install New Outdoor Condenser 
New Filter Drier 
Install Thermostat (Auto Changeover)
Thermostat Wire Included 
Primary Float Safety Switch
Secondary Float Safety Switch 
Install Horizontal Drain Pan
UV Rated Outdoor Insulation 
Refrigerant Locking Caps
Flush Existing Refrigerant Lines
Flush Drain Line
4” Hurricane Pad
Vibration Pads
Hurricane Tie Down Straps
Vacuum System 
Seal Supply/Return Plenums 
Remove Current Equipment
Permitting 
10 Year Parts Warranty
3 Year Labor Warranty 
100% Satisfaction 

*Install Attic Fan
*Vent Bathroom to soffit 
*Duct sanitation
RUUD Equipment (2 Stage)
Install New Air Handler 
Install Air Handler UV System
Install New Outdoor Condenser 
New Filter Drier 
Install Thermostat (Auto Changeover)
Thermostat Wire Included 
Primary Float Safety Switch
Secondary Float Safety Switch 
Install Horizontal Drain Pan
UV Rated Outdoor Insulation 
Refrigerant Locking Caps
Flush Existing Refrigerant Lines
Flush Drain Line
4” Hurricane Pad
Vibration Pads
Hurricane Tie Down Straps
Vacuum System 
Seal Supply/Return Plenums 
Remove Current Equipment
Permitting 
10 Year Parts Warranty
3 Year Labor Warranty 
100% Satisfaction 

*Install Attic Fan
*Vent Bathroom to soffit 
*Duct sanitation
Justin G.
Justin G. Checked in
RUUD Equipment (2 Stage) Install New Air Handler Install Air Handler UV System Install New Outdoor Condenser New Filter Drier Install Thermostat (Auto Changeover) Thermostat Wire Included Primary Float Safety Switch Secondary Float Safety Switch Install Horizontal Drain Pan UV Rated Outdoor Insulation Refrigerant Locking Caps Flush Existing Refrigerant Lines Flush Drain Line 4” Hurricane Pad Vibration Pads Hurricane Tie Down Straps Vacuum System Seal Supply/Return Plenums Remove Current Equipment Permitting 10 Year Parts Warranty 3 Year Labor Warranty 100% Satisfaction *Install Attic Fan *Vent Bathroom to soffit *Duct sanitation
St. Petersburg, FL 33703
Upon my inspection, I found the evaporator Blower Motor is faulty and will not turn off. Replaced 1/2 hp ecm blower motor, Cleaned blower housing and blower wheel. Found evaporator coils were dirty and needed cleaning. Performed an in place evaporator coil cleaning. Cleaned drain line and drain pan with treatment. Wiped down entire air handler inside and outside. Found small piece of insulation missing on drain line. Installed new piece of insulation in the spot and wrapped it up with duct tape. At condenser, found a fried compressor wire at the Contactar. Replaced Contactar complimentary and repaired wire with new connector. Found bad capacitor. Replaced capacitor. Found compressor wire inside condenser unit near the compressor was rubbing up against copper and almost rubbed all the way through the wire insulation. Wrapped up wire with electrical tape and strapped wire up to avoid rubbing. Checked system pressures. System is cooling properly at this time. 
Start up amp draw on compres
Upon my inspection, I found the evaporator Blower Motor is faulty and will not turn off. Replaced 1/2 hp ecm blower motor, Cleaned blower housing and blower wheel. Found evaporator coils were dirty and needed cleaning. Performed an in place evaporator coil cleaning. Cleaned drain line and drain pan with treatment. Wiped down entire air handler inside and outside. Found small piece of insulation missing on drain line. Installed new piece of insulation in the spot and wrapped it up with duct tape. At condenser, found a fried compressor wire at the Contactar. Replaced Contactar complimentary and repaired wire with new connector. Found bad capacitor. Replaced capacitor. Found compressor wire inside condenser unit near the compressor was rubbing up against copper and almost rubbed all the way through the wire insulation. Wrapped up wire with electrical tape and strapped wire up to avoid rubbing. Checked system pressures. System is cooling properly at this time. 
Start up amp draw on compres
Michael A.
Michael A. Checked in
Upon my inspection, I found the evaporator Blower Motor is faulty and will not turn off. Replaced 1/2 hp ecm blower motor, Cleaned blower housing and blower wheel. Found evaporator coils were dirty and needed cleaning. Performed an in place evaporator coil cleaning. Cleaned drain line and drain pan with treatment. Wiped down entire air handler inside and outside. Found small piece of insulation missing on drain line. Installed new piece of insulation in the spot and wrapped it up with duct tape. At condenser, found a fried compressor wire at the Contactar. Replaced Contactar complimentary and repaired wire with new connector. Found bad capacitor. Replaced capacitor. Found compressor wire inside condenser unit near the compressor was rubbing up against copper and almost rubbed all the way through the wire insulation. Wrapped up wire with electrical tape and strapped wire up to avoid rubbing. Checked system pressures. System is cooling properly at this time. Start up amp draw on compres
St. Petersburg, FL 33705
Michael A.
Michael A. Checked in
Installation of Aroma 360 scent device into hvac systems.
St. Petersburg, FL 33704
Ricky O.
Ricky O. Checked in
Will do free tuneup on system with valve replacement Maint plan
St. Petersburg, FL 33701
Justin G.
Justin G. Checked in
On arrival found unit not operating due to blown fuse. Replaced fuse and tested. Found fuse blew due to shorted thermostat. Replaced thermostat. Start and test. Unit operating properly at this time.
St. Petersburg, FL 33704
Return to perform leak search on system. Found link in condenser coil side. Will be able to weld leak and charge system back to factory specs. Further diagnosis could potentially be needed once system is fully running. Sending estimate for repair vs replacement 





Will need to perform whole system search to determine what part or 
area is leaking. Parts may need to be ordered after search. Compressor side holds 13lb of refrigerant. Will need to add refrigerant after repair (1425$). This does not include repair.
Return to perform leak search on system. Found link in condenser coil side. Will be able to weld leak and charge system back to factory specs. Further diagnosis could potentially be needed once system is fully running. Sending estimate for repair vs replacement 





Will need to perform whole system search to determine what part or 
area is leaking. Parts may need to be ordered after search. Compressor side holds 13lb of refrigerant. Will need to add refrigerant after repair (1425$). This does not include repair.
Nathan A.
Nathan A. Checked in
Return to perform leak search on system. Found link in condenser coil side. Will be able to weld leak and charge system back to factory specs. Further diagnosis could potentially be needed once system is fully running. Sending estimate for repair vs replacement Will need to perform whole system search to determine what part or area is leaking. Parts may need to be ordered after search. Compressor side holds 13lb of refrigerant. Will need to add refrigerant after repair (1425$). This does not include repair.
St. Petersburg, FL 33711
Performed Maitenences on systems. Cleaned/treated drain lines, condensate pumps, and primary drain pans. Cleaned condenser coils. Evaporator coils are clean. Verified safety float switchs functionality. Checked amp draw on compressors. Checked amp draw on fan motors. Checked capacitors are not within factory range. Recommending replacing both systems capacitors as they are both out of factory tolerance range. Found main condenser high voltage connector to condenser service panel was loose and broken off. Made necessary repairs. Also found compressor wire to the capacitor start terminal was damaged and at risk of shorting out. Made new wire connection. Made sure all connections are tight. Main system is  cooling with 20° temperature split at this time However the Master bedroom system is low on refrigerant and we recommend adding an estimated 3lbs of refrigerant to achieve proper subcool to start since we have not added refrigerant to this system in the past. On the next Maitenence we w
Performed Maitenences on systems. Cleaned/treated drain lines, condensate pumps, and primary drain pans. Cleaned condenser coils. Evaporator coils are clean. Verified safety float switchs functionality. Checked amp draw on compressors. Checked amp draw on fan motors. Checked capacitors are not within factory range. Recommending replacing both systems capacitors as they are both out of factory tolerance range. Found main condenser high voltage connector to condenser service panel was loose and broken off. Made necessary repairs. Also found compressor wire to the capacitor start terminal was damaged and at risk of shorting out. Made new wire connection. Made sure all connections are tight. Main system is  cooling with 20° temperature split at this time However the Master bedroom system is low on refrigerant and we recommend adding an estimated 3lbs of refrigerant to achieve proper subcool to start since we have not added refrigerant to this system in the past. On the next Maitenence we w
Michael A.
Michael A. Checked in
Performed Maitenences on systems. Cleaned/treated drain lines, condensate pumps, and primary drain pans. Cleaned condenser coils. Evaporator coils are clean. Verified safety float switchs functionality. Checked amp draw on compressors. Checked amp draw on fan motors. Checked capacitors are not within factory range. Recommending replacing both systems capacitors as they are both out of factory tolerance range. Found main condenser high voltage connector to condenser service panel was loose and broken off. Made necessary repairs. Also found compressor wire to the capacitor start terminal was damaged and at risk of shorting out. Made new wire connection. Made sure all connections are tight. Main system is cooling with 20° temperature split at this time However the Master bedroom system is low on refrigerant and we recommend adding an estimated 3lbs of refrigerant to achieve proper subcool to start since we have not added refrigerant to this system in the past. On the next Maitenence we w
St. Petersburg, FL 33703
Fan running non stop due to shorted Thermosat. Replaced with home owner provided nest. Verified system operations 

Had to use white for reversing valve because system does not have enough wires for back up heat.
Fan running non stop due to shorted Thermosat. Replaced with home owner provided nest. Verified system operations 

Had to use white for reversing valve because system does not have enough wires for back up heat.
Nathan A.
Nathan A. Checked in
Fan running non stop due to shorted Thermosat. Replaced with home owner provided nest. Verified system operations Had to use white for reversing valve because system does not have enough wires for back up heat.
St. Petersburg, FL 33714
On arrival found unit not cooling due to bad condenser fan motor. Replaced fan. Start and test. Unit has been fully submerged in salt water with heavy corrosion. Made client aware unit can fail at any point. Client declined system replacement estimate at this time. Unit cooling.
On arrival found unit not cooling due to bad condenser fan motor. Replaced fan. Start and test. Unit has been fully submerged in salt water with heavy corrosion. Made client aware unit can fail at any point. Client declined system replacement estimate at this time. Unit cooling.
Justin G.
Justin G. Checked in
On arrival found unit not cooling due to bad condenser fan motor. Replaced fan. Start and test. Unit has been fully submerged in salt water with heavy corrosion. Made client aware unit can fail at any point. Client declined system replacement estimate at this time. Unit cooling.
St. Petersburg, FL 33703
Justin G.
Justin G. Checked in
Replaced weak fan capacitor for air handler. Start and test. Unit cooling properly at this time.
St. Petersburg, FL 33714
Performed Maitenence on system. Cleaned/treated drain line and primary drain pan. Inspected condenser coils. Evaporator coils are clean. Verified safety float switch functionality. Checked amp draw on compressor. Checked amp draw on fan motor. Fan motor is pulling .94 amps with a max rating of .6. Fan motor is over amping and at risk of failure. Checked capacitor is not within factory range (reading 40 out of 45 with a tolerance of 5%. Replaced capacitor. After replacing capacitor, fan motor amp draw is at .82.  Inspected Contactar. Made sure all connections are tight. System is cooling with a 20° temperature split at this time.
Client had concerns of humidity. Found multiple holes and leaks in old duct work. Recommending duct work replacement and sent quote to client. Included air purification systems with duct work quote per clients request.
Performed Maitenence on system. Cleaned/treated drain line and primary drain pan. Inspected condenser coils. Evaporator coils are clean. Verified safety float switch functionality. Checked amp draw on compressor. Checked amp draw on fan motor. Fan motor is pulling .94 amps with a max rating of .6. Fan motor is over amping and at risk of failure. Checked capacitor is not within factory range (reading 40 out of 45 with a tolerance of 5%. Replaced capacitor. After replacing capacitor, fan motor amp draw is at .82.  Inspected Contactar. Made sure all connections are tight. System is cooling with a 20° temperature split at this time.
Client had concerns of humidity. Found multiple holes and leaks in old duct work. Recommending duct work replacement and sent quote to client. Included air purification systems with duct work quote per clients request.
Michael A.
Michael A. Checked in
Performed Maitenence on system. Cleaned/treated drain line and primary drain pan. Inspected condenser coils. Evaporator coils are clean. Verified safety float switch functionality. Checked amp draw on compressor. Checked amp draw on fan motor. Fan motor is pulling .94 amps with a max rating of .6. Fan motor is over amping and at risk of failure. Checked capacitor is not within factory range (reading 40 out of 45 with a tolerance of 5%. Replaced capacitor. After replacing capacitor, fan motor amp draw is at .82. Inspected Contactar. Made sure all connections are tight. System is cooling with a 20° temperature split at this time. Client had concerns of humidity. Found multiple holes and leaks in old duct work. Recommending duct work replacement and sent quote to client. Included air purification systems with duct work quote per clients request.
St. Petersburg, FL 33703
St. Petersburg, FL - Back yard GFCI was not in a weather proof cover and had a sprinkler right next to it 
Replaced receptacle with a new Weather resistant GFI and a in use exterior cover to protect it from the sprinkler 
After installing the recep did not a have a equipment ground 
Installed a no equipment ground sticker in the box for code compliance 

On front of the home the gfi plug was operating properly when Christmas light were plugged it caused them to trip because water had gotten into the connections 
Tested this on other outlets and they also tripped 
There was a gfi plug also in the front of the house that was not working and had to power to it had to remove it and put a blank plate on the box believe it lost power from somewhere in the crawl space the customer did not want to trouble shoot at this time
Griffin K.
Griffin K. Checked in
Back yard GFCI was not in a weather proof cover and had a sprinkler right next to it Replaced receptacle with a new Weather resistant GFI and a in use exterior cover to protect it from the sprinkler After installing the recep did not a have a equipment ground Installed a no equipment ground sticker in the box for code compliance On front of the home the gfi plug was operating properly when Christmas light were plugged it caused them to trip because water had gotten into the connections Tested this on other outlets and they also tripped There was a gfi plug also in the front of the house that was not working and had to power to it had to remove it and put a blank plate on the box believe it lost power from somewhere in the crawl space the customer did not want to trouble shoot at this time
St. Petersburg, FL 33703
Pulled and clean evap coil. Wiped inside of cabinet. Performed maintenance on system. Cleaned outdoor coil. Cleared pan and drain. Checked electrical. Unit cooling and operating properly at this time.
Pulled and clean evap coil. Wiped inside of cabinet. Performed maintenance on system. Cleaned outdoor coil. Cleared pan and drain. Checked electrical. Unit cooling and operating properly at this time.
Justin G.
Justin G. Checked in
Pulled and clean evap coil. Wiped inside of cabinet. Performed maintenance on system. Cleaned outdoor coil. Cleared pan and drain. Checked electrical. Unit cooling and operating properly at this time.
St. Petersburg, FL 33713
Performed Semi Annual Tuneup 

*Primary safety switch was not installed in line with drain line per install estimate 
*Secondary safety switch not installed in pan per install estimate 

Actuator valve is slamming due to failing or installed backwards. If valve was replaced during install it was installed backwards causing banging sound during start up and shut off. Recommend properly installing valve. Explained that if ball valves were not replaced when we go to install actuator and they do not hold. Than we would need to have lines freezer and replace ball valves. 

Line set not insulated properly causing condensation on ceiling below unit
Performed Semi Annual Tuneup 

*Primary safety switch was not installed in line with drain line per install estimate 
*Secondary safety switch not installed in pan per install estimate 

Actuator valve is slamming due to failing or installed backwards. If valve was replaced during install it was installed backwards causing banging sound during start up and shut off. Recommend properly installing valve. Explained that if ball valves were not replaced when we go to install actuator and they do not hold. Than we would need to have lines freezer and replace ball valves. 

Line set not insulated properly causing condensation on ceiling below unit
Nathan A.
Nathan A. Checked in
Performed Semi Annual Tuneup *Primary safety switch was not installed in line with drain line per install estimate *Secondary safety switch not installed in pan per install estimate Actuator valve is slamming due to failing or installed backwards. If valve was replaced during install it was installed backwards causing banging sound during start up and shut off. Recommend properly installing valve. Explained that if ball valves were not replaced when we go to install actuator and they do not hold. Than we would need to have lines freezer and replace ball valves. Line set not insulated properly causing condensation on ceiling below unit
St. Petersburg, FL 33701
On arrival found unit not operating due to shorted disconnect. Replaced part. Start and test. Unit operates in heating and cooling modes properly.
On arrival found unit not operating due to shorted disconnect. Replaced part. Start and test. Unit operates in heating and cooling modes properly.
Nathan A.
Nathan A. Checked in
On arrival found unit not operating due to shorted disconnect. Replaced part. Start and test. Unit operates in heating and cooling modes properly.
St. Petersburg, FL 33713
Estimate for mini splits and slit system.
Estimate for mini splits and slit system.
Justin G.
Justin G. Checked in
Estimate for mini splits and slit system.
St. Petersburg, FL 33713
How do I know if my AC needs repair or full replacement?

Our technicians inspect the full system — age, refrigerant type, corrosion, and repair history — and give you an honest recommendation. If a repair makes sense, we'll fix it. If the unit is beyond its useful life, we'll walk you through replacement options with no pressure.

Are your technicians background-checked and licensed?

Yes. Every Air Bros technician is background-checked, factory-trained, and works under our state HVAC license (#CAC1820499) and electrical license (#EC13015085).

What parts of St. Petersburg do you serve?

We serve all of St. Petersburg, including Downtown, Historic Kenwood, Old Northeast, Snell Isle, Crescent Lake, Shore Acres, and Coquina Key, plus Seminole, Largo, Pinellas Park, and the surrounding beach communities.

Do you offer same-day AC repair in St. Petersburg?

Yes. We offer 24/7 emergency AC repair with same-day service throughout St. Petersburg and the surrounding Pinellas County area.

Is Air Bros a local St. Petersburg company, or a franchise?

Air Bros is 100% locally owned and operated, headquartered in the Shore Acres neighborhood of St. Petersburg. We're not a franchise — every technician is a direct employee, not a subcontractor.

Contact the Bros You Know Today!

Gravity Forms Pagination Must be Steps