Largo, FL

Compressor shorted to ground

Upon arrival, the homeowner stated that water was leaking through the ceiling and had noticed water around the air handler. After performing a diagnostic, I found that the condensate drain line was clogged, causing water to back up into the system and overflow onto the floor, which resulted in the ceiling leak. I completed a full system inspection and found a 20°F temperature difference between the supply and return, healthy refrigerant pressures, and all electrical components operating properly. I performed a condensate drain line treatment and verified that the drain line was flowing and draining properly after the service. At this time, the system is operating as designed. If you have any questions, please don’t hesitate to reach out. Thank you for your business, and have a great day!

Found clogged drain line. Cleaned and treated drain line and primary pan. Found system cooling with 10° split. Added 2lbs refrigerant and cleaned condenser coils. System now has good pressures and a 16-17° split. Let client know system may have a refrigerant leak. We will check pressures annd temp split again on next visit.

Found bedrooms not cooling properly due to original sheet metal ductwork. Bedrooms are recommended to be on separate mini split systems to guarantee proper comfort for rooms. Client is aware of age of ductwork and main unit. Told client to plan to replace in near future. Unit is cooling to the best of its ability at this time.

Diagnostic -drain line backing up causing system to intermittently shut off -outside capacitor reading weak on compressor side -Subcool value high due to dirty outdoor coils Scope of work -flush drain line & drain pan -added pan tablets to help with buildup -clean outdoor condenser coils -replace outdoor capacitor -taped spliced outdoor wiring -removed failed hard start kit Verified system is cooling & draining Complimentary cleaned outdoor coils Taped outdoor wiring Fan speed on low

Replace capacitor Replace Contactor Diagnostic charge Cleaned condenser coils System is operating *Raining during visit

On arrival found multiple issues with system. Pressures are reading incorrectly due to improper air flow. Evaporator coil extremely clogged and found issues with ductwork. Due to condition of system we are only able to provide a new system estimate. Will submit quote. Unit is cooling to the best of its ability.

Upon my inspection, found system #2 air handler secondary drain pan completely full of water. Performed lvl.3 drain cleaning and treatment on system. Drain line is draining properly at this time. Advised client to keep fan in the on position for 2 days and then return to auto afterwards in order to dry the air handler out. If this issue persists, we will need to replace the evaporator coil/primary drain pan under parts warranty if applicable. This primary drain pan could have a crack and letting water escape the unit. I noticed there’s evidence of rodent damage in the attic where multiple ducts have holes and one duct connection is separated. In the winter time we can address this issue by replacing the damaged ducts. Replaced air filter for system. System is cooling with a 20° temperature split at this time.

Replace high pressure switch solder on stem of discharge line Replace all 7.02 pounds of 410 A Replace drier on liquid line

Client states system cannot keep up during the day and it is getting worse. Her husband added refrigerant before he had to leave but they don’t think it solved the issue. Upon my inspection, I found the refrigerant circuit has a restriction causing the unit to not be able to cool efficiently. This system is an off brand and looks to be from 2010. We are not comfortable making the repair on this system given its age and that it’s not a reputable brand. A repair would look like a new TXV, new Liquid line filter drier, and all new refrigerant. We are providing an option to replace this system given its current condition and off brand in order to guarantee proper cooling with new warranties. Quote is being sent to clients email.

Found completely bad capacitor. Replaced capacitor and started system. Amp draws are good on compressor and fan motor. Rinsed condenser coils complimentary and plugged compressor harness plug back in as it was beginning to fall out from vibrations. 1 year part warranty on capacitor.

Upon my inspection, found clogged drain line. This was intermittently turning the system off when it drips the safety float switch. Client says system has not been maintenance since it was installed. Explain that all systems need routine maintenance to prevent issues such as this. Performed a drain cleaning and treatment. System is now cooling. System has a 20° temperature split. I also found a supply air leak in the existing ductwork Plenum. Made a small patch to this leak complementary. This repair is unrelated to the install as it is existing ductwork. Our connection from the air handler to that duct. Plenum is still sealed properly. Recommending our Maitenence plan

Performed Maitenence on system. Cleaned/treated drain line and primary drain pan. Cleaned condenser coils. Evaporator coils are clean. Verified safety float switch functionality. Checked amp draw on compressor. Checked amp draw on fan motor. Checked capacitor is within factory range. Inspected Contactar. Made sure all connections are tight. System is cooling with a 20° temperature split at this time. No visible growth inside air handler at this time. Blower wheel is clean as well. Client signed up for 1 system Maitenence plan. Client says there has always been issues with their back room getting air flow. Let client know duct work is very old and some parts are collapsing and they should plan for duct work replacement in the future if they would like to resolve these issues.

On arrival found unit not cooling due to thermostat not sending proper signal to condenser. Client declined replacement of thermostat and will change themselves. Explained to client our thermostats are covered by warranty through our company. Reset power and unit operates at this time.

Reason for call: Member tuneup Equipment: 2020 trane 2.5 ton Vertical in closet Condenser on right side of home Summary: Completed tune up to find dirty blower assembly. All equipment is operating within manufacturing specifications. Confirmed pressures, temps, and amps. Checked cap readings. Clean drain line and condensation pump. Flushed both indoor and outdoor coils. Solution: Recommended uv treatment and cleaning of blower assembly across three repair options.

Reason for call: No cool Equipment: 2020 condenser Goodman 2011 air handler Goodman Summary: Found failed capacitor and buzzing contactor. Replaced both starting components operation was restored to the equipment unit is cooling with a 20 degree split.

3 Ton American standard system not cooling for conference room. Upon my inspection? Found system not cooling due to clogged condensate line and pan. Scope of work: Condensate Drain cleaning and treatment Now cooling with a 20° temperature split Authorized approval and payment from Lori Could not get in contact with landlord Ken. Lori called and told Ken that she is approving the work to be done and authorized payment

Upon arrival, I began by checking the temperature differential between the supply and return air and measured a 20°F split, which is within a healthy operating range. I then evaluated the refrigerant circuit and found no signs of leaks, restrictions, or abnormal operating conditions. Refrigerant pressures and system performance were operating as expected. Next, I inspected the electrical components. All components are operating within their proper amperage ranges, and no shorts, burnouts, or electrical failures were found during testing. After completing the diagnostic, I determined that the system is functioning properly from a mechanical and electrical standpoint, with no current issues affecting operation. Based on my findings, it appears the drain line condition caused the float switch to activate, which intermittently shut the system off throughout the day. I performed a drain line treatment to help prevent future blockages and relocated the float switch to a more appropriate p

Reason for call: Ac not keeping up Equipment: 2025 Lennox 3 ton heat pump Vertical in closet Condenser out back Summary: Completed diagnosis to confirm refrigerant pressures were low. Gave homeowner option was to charge system sign up on membership for reevaluation. Or do leak search today. She chose to fill up and sign up on membership. System have felt the same since install and her old company informed her the installers who did this job were "fired due to drug use" Performed visual leak search today confirmed all braze joints are good and no oil spots in coils. Solution: System has felt the same since install. We will top of charge. Reevaluate at first maintenance visit

Upon arrival, I checked System #1 downstairs and recorded a 23° temperature difference, which is within a healthy operating range. I then checked System #2 and recorded a 20° temperature difference, also within a healthy range. I inspected the electrical components on both systems, and everything is functioning properly with no issues or concerns at this time. I also performed condenser cleanings, drain line treatments, and full air handler inspections on both systems. At this time, both systems are operating properly and efficiently. If you have any questions or concerns, please feel free to reach out. Thank you for your business, and have a great day.

Install dual capacitor. Duct seal in three connections. Finish tune up from yesterday.

Reason for call: Tune up on two systems Equipment: 2022 rheem Horizontal in second floor closet Condenser on left side of home 2019 Goodman Horizontal in first floor attic Condenser is on left side of home Solution: Rheem new capacitor Rheem needs duct seal Work was sold for tmr due ti weather Summary: Completed tune ups minus flush drain will handle tmr with repairs. Goodman is in fair condition pressures and temps were spot on Rheem isn't running due to shut off on high head pressure confirmed cap is dead will be replaced tmr.

Reason for call: No cool Equipment: 2013 package unit Summary: on arrival found after market fan motor recently installed on condenser. Found capacitor dead. Found disconnect to have poor connection holding out voltage. Replaced both capacitor and disconnect. Operation was restored to equipment. Solution: Replaced disconnect and fan capacitor. Informed homeowner of age and condition of equipment. Signed homeowner up on membership.

Replace 150 amp main panel Run a new Electrcial chase Install new surge protector Relabel panel directory

Client states system is not cooling. Found the cooling wire not getting voltage from the thermostat to the condenser. Took the thermostat off the wall and jumped out cooling and system turned on. Reconnected the thermostat and tested system and system began running. There may be an intermittent issue with this thermostat. At this time, the system is cooling and the client would like to leave it. While here, the system is due for a six month Maintenence. Performed Maitenence on system. Cleaned/treated drain line and primary drain pan. Cleaned condenser coils. Evaporator coils are clean. Verified safety float switch functionality. Checked amp draw on compressor. Checked amp draw on fan motor. Checked capacitor is within factory range. Inspected Contactar. Made sure all connections are tight. System is cooling with a 20° temperature split at this time.