Gulfport, FL

On arrival found unit not cooling due to tripped float. Cleared pan and drain. Added pan tabs to system. Observed weak capacitor and low refrigerant. Filled unit back to factory specs and replaced weak capacitor. Pressures good. Temp split good. Unit draining and cooling properly at this time.

Home owner has concerns humidity and lack of air flow in some areas Found air handler holding water due to clogged drain line Found system low refrigerant (1.5lb) (previous contractor working on system) (explained we can charge system and monitor pressures) Home owner asked about dryer venting, explained we do not offer dryer vent services Addition/enclosure master bedroom/bathroom lack of air flow. Found wholes in ducting and ducts lacking insulation. Some ducts have been taped. Air handler is furthers from these areas Explained in the winter time we can come back to design a duct system to meet there homes requirements. Also recommended we could add mini split to addition Scope of work -Cleared drain line and drain pan -add pan tablets/solution to help with buildup -Primed trap and drain -added 1.5lb 410a back to factory specifications Will return in colder months to go over ducting

Replace warranty outdoor suction temp sensor. Unit cooling properly.

Client installed Mr. cool mini split single zone system. Found system very low on refrigerant. Explained that we can do a leak search and repair depending on where the leak is but client would like to hold off and fix it himself. System is not cooling at this time. Client noted that he did not pull a vacuum when releasing the refrigerant in the lineset. I explained that noncondensables will shorten the lifespan of a system and not allow it to work properly.

Found unit cooling on arrival. Error code reflects faulty temp sensor. Unit is still operational. Will submit estimate for sensor replacement.

System not cooling. Found condenser fan motor seized up. Replaced fan motor and started system. System is cooling at this time. Amp draws are good. 1 year warranty on motor

Found system running but compressor not coming on. Sound bad capacitor. Replaced capacitor and contactor. Started system and found amp draws and temperature splits are within range. Temperature split is at 19°. Performed a complementary drain cleaning. System is cooling and draining properly at this time.

3.5 ton Ruud system 14.3 seer 2 10 year parts warranty 3 year labor warranty -Shorty air handler -Permit -Condenser on existing stand with vibration pads -New electrical disconnect outside -Reinsulate all copper outside with uv resistant armorflex -Hurricane tiedowns -New electrical whip -Corrosion protection sprayed on condenser -Float switch -Seal to existing plenum -10kw heater -Replace breakers as needed -Uv light installed above coil -Flush drain -New Honeywell thermostat -100% satisfaction guarantee

2 Year Goodman Heat Pumps (2 Systems) Performed maintenance on both systems Systems are operating within manufacture specifications

Redo both flare fittings at condenser Perform pressure test Pull deep vacuum Recharge with 1.6 pounds of R32 Warranty flare on Condneser repair for 1 year. Informed homeowner of regular cleaning on mini split every other year. Pressure test held at 286.0 for 10 min Pull vac down to 500 m Charged system with 2.9 of 32

Reason for call: Mini split no cool Equipment: 2025 single zone Daikin Summary: On arrival found system extremely low on refrigerant charge. Found leaking flare fitting at Condenser. Quoted to redo both fitting at condenser. Perform pressure test to confirm no other leaks. Pull deep vacuum in system recharge system with 1.6 pound of R32. Pressure we reading 117 standing

Client had bad blower motor but it was replaced by another company less than a year ago. Gave her price of 1,450$ she’s calling other company to see if they will warranty

Ruud 4 ton 15.2 seer2 heat pump split system with 5kw heater Anchor condenser Material lift WiFi thermostat Primary float switch Media filter Clear drain Uv rated insulation for outdoor copper Refrigerant locking caps Remove existing equipment Connect to existing ducts and electrical Seal unit to code Tax labor and permit included 10 year parts warranty 3 year labor warranty

We tried to schedule Maitenences twice before today’s visit. Found clogged drain line and faulty safety float switch today. Performed rest of Maitenence today. Amp draws, contactar, and capacitor are good. Temp split is 19°. Cleaned condenser coils. System is cooling at this time Replaced ss2 safety switch Performed discounted drain cleaning.

Reason for call: Tune up turned into no cool Equipment: 2015 Goodman 3 ton straight cool Condenser on roof Air handler vertical in storage closet Summary: On arrival found condenser breaker tripping. Unit not cooling. Found dead capacitor and found compressor stuck in start up. Unit needs new capacitor and new starting components. Informed homeowner he wanted a quote for replacement. Provided repair and replacement quote to homeowner.

Reason for call: Condensate pump running more than normal. Equipment: 2 zone hunter and cooper mini split Summary: Performed tune up in both mini split heads. To find them cooling very well. Confirmed proper pressures, temperatures. Flushed coils and drain line. Inspected blower wheels to find both units need to be cleaned. Found condone pump operating very well more water is being produced at the warm season arrives. Homeowner only wanted mini split and inspected not central unit.

Upon arrival, I spoke with the tenant regarding the reported issue. The tenant stated that the condensate drain line had backed up into the float switch the previous day, causing the system to shut down. Before recommending any repairs or cleaning services, I performed a complete system diagnostic. The system is mechanically operating properly at this time. The refrigerant cycle is healthy with no signs of leaks or restrictions, the temperature differential is approximately 20°F and within the proper operating range, and all electrical components are functioning as designed. Based on my findings, the issue appears to be related to the condensate drain system. I recommended an advanced drain line cleaning to thoroughly clear the line and help prevent future backups. However, since I was onsite approximately one month ago for a maintenance visit, I am offering the service at the Tier 1 cleaning rate. Once the cleaning is completed, I can confidently verify that the drain line is clear

Replace evap coil, replace stat Proper operation was restored to equipment.

Found leaky evap coil. Client does not want to replace system due to them selling the home. Replacing coil on monday

Upon arrival, I checked the temperature difference between the supply and return air and recorded a 17° split. I then proceeded with a full electrical inspection and found all electrical components functioning properly with no signs of shorts, burnouts, or over-amperage conditions. I performed a drain line treatment, cleaned the condenser coil, and completed an inspection of the air handler. During the inspection, I noticed the blower wheel has buildup/impact from dust accumulation. I recommended a blower wheel cleaning (pollen clean) to improve airflow and system efficiency; however, the homeowners chose to hold off on the service at this time. If you have any questions, please feel free to reach out. Thank you for your business, and have a great day.

On arrival found condensate pump fitting broke and leaking water in return. Replaced pump. Changed electric to match new pump. Connected float. Start and test. Pump operating properly. Unit cooling at this time.

Install New Air Handler Coil Under Manufacturer Warranty Pulled vacuum and pressure test Charged system to manufacture specifications Unit is currently operating within manufacture specifications

Replacement of two 6 in flex runs One located off mixing box feeding master bed has huge hole One located off mixing box feeding back room Bring 2 full bags of 6in reuse collars

Completed tune up to find operation of unit within manufacturing specifications. Found blower wheel has biological growth, no primary float switch, duct work is not strap properly, 4 in run has collapsed on itself. Unit is operating there repairs will improve the operation, efficiency, and life expectancy of equipment.

Upon arrival tenant states unit is not cooling. Found outdoor board had failed. Bypassed board and system began to run. Found thermostat shorting across heat terminal causing system to run in heat. Found large hole in 6” flex duct in attic (potential rodent) Recommendations -outdoor contactor pitted and rusted -outdoor compressor capacitor reading out of specs -outdoor coils impacted with dirt/debris -no primary overflow safety on air handler (potential water damage) -Thermosat needs to be replaced (shorted) Went over concern with homeowner. Also went over basic maintenance with tenant (filters etc) Would recommend adding surge protectors to avoid this issue Unit is currently cooling but will need to get board from supplier. Will not run in heat until thermostat replaced. Casey (Tenant) 860-961-8493